The hands will then return to the current time. Remove the watch from your wrist and place on a stable surface in a location, such as near a window, from which radio waves can be easily received, pointing the side reception antenna position in the direction of the radio wave transmitter.
The watch will automatically receive the radio wave every day at 2 a. If it successfully receives the wave, reception is not performed at 3 a. An antenna for receiving the radio signals is located inside the watch on the position.
Return the crown to the normal position. Remove the watch from your wrist and place on a stable surface near a window where the radio signal can be easily received.
Point the side of the watch in the direction of the radio wave transmitter, and hold down the lower right button A for more than 2 seconds. Release when the confirmation tone sounds and the second hand stops at RX.
The second hand will then move to H, M or L. When the radio wave has been properly received, the second hand will automatically move from H, M or L to the time that was received, all the hands will be corrected, and the second hand will return to 1-second interval movement. When the watch is recharged sufficiently, it will automatically receive the radio wave once.
Even though the watch will not show movement, the correct time is kept in memory. When the watch is in the Power Save mode, it will continue to keep the correct time internally. Refer to page 92 for information on the Power Save Function. Poor Reception Areas It may not be possible to receive radio waves under environmental conditions where reception is difficult or in areas susceptible to radio noise, such as those shown in the illustrations below.
While referring to the reception level display, try to find a location with better reception. Display during Reception [During reception standby] [Receiving signal] [Reception completed] [Second hand display] Radio wave reception indicator j The second hand moves from RX to reception level H, M or L and reception starts.
The radio wave reception indicator points to the received transmitter. Reception can take from about 2 minutes to a maximum of 15 minutes, depending on factors such as the weather or noise. If the radio wave reception fails, the watch may return immediately to the normal display. Do not move the watch until the second hand has returned to 1-second interval movement. Press the lower right button A once to display the reception status. Press the lower right button A once. The standard time radio wave to be received can be changed by selecting the city in another region.
The maps show the approximate reception areas. The reception area on the map is only guideline, and it may be difficult to receive the radio signal even within the areas indicated on the map. World City Display UTC Coordinated Universal Time and 43 cities or regions are registered in this watch in advance, and it is also possible to register one additional city.
The time of each city can be called up and displayed. It uses leap seconds to correct deviations in time systems that are based on the rotation of the Earth universal time. We recommend that you regularly check the charge level and keep it at level 2 or above.
Recharge the watch immediately. The insufficient charge warning is activated at this level. The charging level is rather low. Recharge the watch. The charge condition is good. The watch can be used normally at this level. The watch is sufficiently charged. The watch is fully charged and can be used normally at this level. Charge level display Remaining time approximate [Caution] When the charge level indicator points at level 0, the secondary battery is very low.
The second hand moves at 2-second intervals, and the mark flashes in the digital display. After about three days the battery will run out and the watch will stop. Be sure to recharge the watch before this condition is reached. Pull the crown out to position 1 mode switching position. Turn the crown to the right or left to align the mode hand with the desired mode.
Press button A and button B at the same time. Turn the crown to return to the original mode. Return the crown to the normal position to complete the operation.
Switch The hands also change at the same time. There may be cases when the time is not changed on the appropriate date. Whether or not the system is used and the length of use differs between countries and regions.
Pull the crown out to position 1 and turn to align the mode hand with TME time mode. Press button A or B to call up the city name whose time you want to correct. Pull the crown out to position 2 to enter the time correction status. The new correction location will begin flashing. Press the upper right button B to enter the second correction status. Press the upper right button B to enter the minute correction status.
Turn to the right to move forward and to the left to move back. To stop, turn the crown to the left or right. Press the upper right button B to enter the hour correction status.
Pull the crown out to position 1 and turn to align the mode hand with CAL calendar mode. Press button A or B to call up the city name whose date you want to correct.
Pull the crown out to position 2 to enter the date correction status. Each time the upper right button B is pressed, the correction location changes. Select the correction location and turn the crown to correct the time.
After the end of measurement, the time-up tone sounds for about 5 seconds and the watch returns to the timer initial setting status. Pull the crown out to position 1 and turn to align the mode hand with TMR timer mode. Pull the crown out to position 2 to enter the timer setting status. Minute display flashes Settings complete [Digital display 2] 54 3. Turn the crown to set the time. After completing the settings, return the crown to the normal position.
A confirmation tone will sound each time you press the upper right button B to start and stop the measurement. The measurement mark comes on during measurement. Press the lower right button A during measurement to return to the initial set time and start measurement again. Press the lower right button A while the timer is stopped to return to the initial set time. Button B 4. When the time is up, END is displayed in digital display 2 and the time-up tone sounds for 5 seconds. Press the lower right button A during measurement to display a split time for 10 seconds.
After the 10 seconds, the watch returns to the measurement status. Press the lower right button A while the chronograph is stopped to return to the chronograph reset status. Users in countries or regions without a radio wave transmitter should make sure that the start date and finish date of daylight saving time are accurate.
Pull the crown out to position 1 and turn to align the mode hand with WT-S world time set mode. Pull the crown out to position 2 to enter the world time correction status.
Turn to the right to change in the direction of cities with more of a time difference, and turn to the left to change in the direction of cities with less of a time difference. Turn the crown to call up HOM for the world city. Press the upper right button B twice to enter the time difference setting status.
Turn the crown to set the time difference. Turn crown to the right or left to stop the quick movement. To stop the alarm, press button A or B. Turn the crown continuously to move quickly. Pull the crown out to position 1 and turn to align the mode hand with AL-1 or AL-2 alarm mode. Pull the crown out to position 2 to enter the alarm correction status. Each time the upper right button B is pressed, the display flashes and the correction location changes.
AU Auto : The time is updated with the daylight saving time from the received radio wave. MAN Manual : The 4 a. It cannot be set to 2 a. OFF Off : Automatic reception is not performed. AUT Auto : Automatic reception is performed according to the initial settings at 2 a. Pull the crown out to position 1 and turn to align the mode hand with RX-S receive set mode. Pull the crown out to position 2 to enter the daylight saving time SMT reception setting status.
Press the lower right button A to select AU or mA. Press the upper right button B to enter the automatic reception setting status.
Press the lower right button A to set the automatic reception operating condition to MAN. Next Page. Troubleshooting Troubleshooting 23 troubleshooting Citizen Eco-Drive Instruction Manual 71 pages. Citizen Eco-Drive Instruction Manual 56 pages. Citizen perpetual calendar ble: user guide 34 pages. Before using the watch, read this instruction manual carefully to ensure correct use.
After reading the manual, store it in a safe place for future reference. Page 5 Safety precautions — IMPORTANT This manual contains instructions that should be strictly followed at all times not only for optimal use, but to prevent any injuries to yourself, other persons or property.
Page 7 If adjustment is not done correctly, the bracelet may unexpectedly become detached leading to loss of your watch or injury. Consult your nearest authorized Citizen service center. Protective stickers Be sure to remove any protective stickers that may be on your watch case back, band, clasp, etc. Otherwise, perspiration or moisture may enter the gaps between Unlock Lock Push the crown in to the case.
With gentle pressure Rotate the crown towards the case, rotate the Screw down counterclockwise until it crown clockwise to secure crown releases from the case. The illustrations in this instruction manual may differ from the actual appearance of your watch. Page Charging Your Watch Charging your watch This watch has a rechargeable cell which is charged by exposing the dial to light, such as direct sunlight or fluorescent lamps.
After taking off the watch, put it in a location where the dial is exposed to bright light, such as by a window. Page 12 Charging your watch When the watch reaches a low charge state insufficient charge warning function When the power reserve becomes low, the second hand moves once every two seconds.
This is the insufficient charge warning function. Be sure to fully charge your watch. Page Charging Time By Environment Charging your watch Charging time by environment Below are the approximate times required for charging when exposing the watch dial to light continuously.
Please use this table as a reference only. Charging time approx. Illuminance To start working To become fully Environment To work for lx normally when the cell charged when the cell is one day is discharged discharged 2 minutes 50 minutes 9 hours A fluorescent lamp or interior lighting does not have sufficient illumination to charge the rechargeable cell efficiently. Page Adjusting The Time Adjusting the time Pull the crown out to position when the second hand points to 0 second.
All the hands stop. Access the Setting Instruction Manual for your particular Citizen watch in one of two ways: 1. Referencing the diagrams below, locate and enter the movement Caliber Number on your watch's caseback in the entry field on this page, then click or tap 'Get Instructions'. Why does my watch appear to have lost time, even t. Simply follow the link provided above and you can directly download citizen eco drive wr manual ppt and save it to your computer or else you can also read online through our library.
CA - Setting Instructions Created Updated Refer to theinstructions below for directions on how to set this watch All Reset All reset is used when first setting the watch or when there is unusual or erratic operation. Zero Position Adjustment After all reset the hands must be 'Zeroed' to provide a starting point for setting the watch.
Pull the crown out to the second click 3 The second hand, minute hand, hour hand, 24 hour hand, UTC hour and minute hand will all rapidly advance to their last remembered 'Zero' position Note: When setting the 'Zero' position of the hands, make sure that you turn the crown in the Clockwise direction 1 - With the crown out to the second click 3 turn the crown to the right clockwise to move the minute hand around the dial until it is 'Zeroed' at the position.
Setting the Time The time on this watch is set by changing the digital display time then transferring the digital time to the hands. Setting the Calendar The calendar in this watch is set in the digital display. To set the calendar follow the steps below. Only the tone that sounds is different. Press button A or B to turn it off To turn the alarm On or Off pull the crown out to the first click 2 and press button B. Using the Chronograph The chronograph can measure and display time up to a maximum of 23 hours, 59 minutes, and After this time the chronograph resets to '0' and stops.
Using the Timer The timer can be set to a maximum of 99 minutes in 1 minute increments. When the set time has elapsed, a tone will sound for about 5 seconds after which the display returns to the original timer setting. Special functions of this watch Zone Setting This watch allows you to display the time and date for up to 31 cities. Adding a custom city and time difference. All Reset. All reset is used when first setting the watch or when there is unusual or erratic operation.
Zero Position Adjustment. After all reset the hands must be 'Zeroed' to provide a starting point for setting the watch. Setting the Time. The time on this watch is set by changing the digital display time then transferring the digital time to the hands. Setting the Calendar.
0コメント